Citrix plugin for iphone
The cache manager is a convenient way to manage the cache and view statistics without logging into the server The cache manager (cachemgr.cgi) is a CGI utility comes with squid for displaying statistics about the squid process as it runs. Remember to restart Squid for the changes to take effect. # Add this at the top of the http_access section of nf # Add this to the bottom of the ACL section of nf # Add this to the auth_param section of nfĪuth_param basic program /usr/lib/squid/ncsa_auth /etc/squid/squid_passwd Here’s a simple user authentication example the order of the statements is important: Finally, create an http_access entry that allows traffic that matches the ncsa_users ACL entry. Next, create an ACL named ncsa_users with the REQUIRED keyword that forces Squid to use the NCSA auth_param method you defined previously. # locate ncsa_auth/usr/lib/squid/ncsa_authĤ) Edit nf specifically, you need to define the authentication program in nf, which is in this case ncsa_auth. ( different distro stores this file at different locations) # htpasswd /etc/squid/squid_passwd nikeshNewģ) Find your ncsa_auth file using the locate/find command. In this case, you add a username called nikesh: You can add users at anytime without having to restart Squid.
CITRIX PLUGIN FOR IPHONE PASSWORD
The name of the password file should be /etc/squid/squid_passwd, and you need to make sure that it’s universally readable.Ģ) Use the htpasswd program to add users to the password file. Squid comes with a program called ncsa_auth that reads any NCSA-compliant encrypted password file.ġ) Create the password file. You can configure Squid to prompt users for a username and password. The vSphere web client can be reached at the following address: Btw: the deafult login for the vCenter 5.1 virtual appliance is user: root and password: vmware That fixed the problem and it didn't delete the cluster and folder settings that I had already configured for this given vCenter server. The solution was to log into the administration web interface, and re-run the configuration wizard with default settings. That seemed a little overkill as the appliance should work or at least you should be able to reconfigure it. I received the following error:įailed to connect to VMware Lookup Service - I found a VMware KB indicating that there could be something wrong with the SSL certificate - because I had changed the FQDN of the appliance after initial setup. It went fairly smooth, however, I couldn't connect to the vSphere web client. Yesterday, I installed the vCenter 5.1 vCenter Virtual Appliance in my home lab. It works like a charm, see screendump below: So, access the web client, locate the VM, right click -> Edit settings, and check the box as mentioned (for the parent VM, not the virtual ESXi.). Check the box next to "Expose hardware-assisted virtualization to the guest operating system." This setting is not available under the traditional C# client." To enable virtualized HV, use the web client and navigate to the processor settings screen. "Virtualized HV is fully supported for virtual hardware version 9 VMs on hosts that support Intel VT-x and EPT or AMD-V and RVI. For ESXi 5.1 this has changed according to this VMware KB.
I seem to remember that in version 5.0 you had to configure a given parameter in the ESXi console. On nested virtual ESX hosts, longmode requires the "Virtualized Hardware Virtualization" flag to be enabled on the outer VM." On Intel systems, longmode requires VT-x to be enabled in the BIOS. It is required for 64-bit guest OS support. When I tried to boot a 64-bit on these hosts I received the following error: In my home lab, I have a 2-node cluster with two virtual ESXi 5.1. After you’ve made the changes close out of the Registry Editor and restart the machine.
Open the Registry and browse to HKEY_LOCAL_MACHINE \ SYSTEM \ CurrentControlSet \ Control \ Power and change both HiberFileSizePercent and HibernateEnabled value data to zero. Now that the disclaimer is out of the way…you might want to completely disable Hibernate mode through a registry edit. Note: Changing registry values can cause your computer to become unstable or stop functioning and is only recommended for experienced users. Type in the following to disable hibernation. The Command Prompt opens and you will use the following to enable Hibernation. Right-click on the icon and select Run as administrator. Click on Start and type CMD into the search box and it will be listed under programs. Using the Command Prompt might be the easiest way to enable or disable Hibernation. Enable or Disable Hibernate Through Command Prompt